Napco Security Technologies GEM-K1CA Manual do Utilizador

1 OPERATING GUIDE for your GEM-K1CA KEYPAD © NAPCO 2005 ARMED COMPUTERIZED SECURITY SYSTEM STATUS GEMINI R 1 2 3 B 4 5 6 C 7 8 9 0 P Q G U SYSTE

10 Disarming the System 1 Enter your premises through the Entry/Exit door. The keypad will sound a steady tone to remind you to disarm the system be

11 FIRE PROTECTION (Applicable only where local ordinance permits use of this alarm control panel for fire protection.) Fire-Zone Alarm If a fire is d

12 FIRE PROTECTION Preparing a Fire Escape Plan Even with the most advanced fire alarm system, adequate protection requires an escape plan. To prepar

13 FIRE PROTECTION Floorplan Draw a plan of your premises in the space provided below. Floorplan

14 FIRE PROTECTION Although a fire alarm system may be of a reliable and state-of- the-art design, neither it nor its peripheral detection devices can

15 FUNCTION MENU The keypad can provide access to a wide assortment of utility functions. The functions are displayed in a prompting “YES/NO” format.

16 Activate Bell Test? Activates the alarm (while disarmed) for about 2 seconds and performs a battery test. If the alarm does not sound, call for ser

17 FUNCTION MENU Reset System Trouble? System troubles display and sound at the keypad. Correcting the trouble will clear most indications, however th

18 FUNCTION MENU Activate Telephone Test? (Telephone Test programmed? YES NO). Sends a communicator test to the central station. A communication fa

19 FUNCTION MENU Activate Program? Activates the Program Mode from Keypad No. 1. Note: This feature is disabled while armed. (See PROGRAMMING USER

2 The GEM-K1CA is a “smart” user-friendly, interactive menu-driven keypad designed for your Napco control panel. Its alphanumeric screen will not onl

20 Your alarm specialist may have programmed your system to be monitored by a central station. The built-in digital communicator can transmit emergen

21 ADVANCED FEATURES Security Bypass/Unbypass (Security Bypass programmed? YES NO). In high-security applications, zones may be bypassed (or unbypa

22 PROGRAMMING (OPTIONAL) Enter the User Program Mode 1. Enter your User Code, then press R to enter the Function Mode. 2. Answer NO until “ACTIVA

23 PROGRAMMING (OPTIONAL) Reviewing a Programmed User Code To review an existing User Code, enter the user number and the corresponding User Code will

24 PROGRAMMING (OPTIONAL) Enter the User Program Mode 1. Enter your User Code, then press R to enter the Function Mode. 2. Answer NO (press Q) unti

25 ENTER ZONE DESCRIPTIONS -- "CELL PHONE STYLE" 1 ABC1 2 DEF2 3 GHI3 4 JKL4 7 STU7 8 VWX8 9 YZ90 6 PQR6 5 MNO5 0 PRESS CHARACTERS DISPLAYE

26 PROGRAMMING (OPTIONAL) Enter the User Program Mode 1. Enter your User Code, then press R to enter the Function Mode. 2. Answer NO (Q) until “ACT

27 KEYPAD MESSAGES The keypad can display the following functional messages. Other diagnostic messages are available for the installer or servicer.

28 KEYPAD MESSAGES Alarm condition, followed by zone description(s). “ALARM” and zones will display after system is disarmed. Note zones, then press C

29 KEYPAD MESSAGES The system is in the process of reporting a cancel signal to central station which will cancel the alarm which it has just reported

3 TABLE OF CONTENTS TABLE OF CONTENTS Section Page KEYPAD CON

30 GLOSSARY Following are brief descriptions of terms and features used herein that may be unfamiliar to you. Some of the features are programmable op

31 GLOSSARY Exit/Entry Delays - Separate delays that let you exit and enter your premises without setting off an alarm when the system is armed. Inst

32 GLOSSARY Zones - Independent circuits that protect specific areas of the premises: Auto-Bypass Zone: A zone that will be automatically bypassed f

33 SYSTEM TROUBLE ERROR CODES Your control panel is capable of detecting a variety of troubles that may affect system performance. In the unlikely eve

34 SYSTEM TROUBLE ERROR CODES Trouble Indication System Trouble Condition Action E04-NN Wireless Transmitter Supervisory Failure A problem has been

35 SYSTEM TROUBLE ERROR CODES Trouble Indication System Trouble Condition Action E10-NN Keypad Response Failure Call installing company for service

36 SYSTEM TROUBLE ERROR CODES Trouble Indication System Trouble Condition Action E19-00 User Program Memory Error Call installing company for servic

37 SYSTEM TROUBLE ERROR CODES Trouble Indication System Trouble Condition Action E40-00 RF Self Test Failure A wireless motion sensor on the zone i

38 TROUBLESHOOTING What do I do if... For more info... I try to arm my system but the keypad just displays “ZONES NOT NORMAL” and “CAN’T ARM SYSTEM

39 NOTES

4 KEYPAD CONTROLS & INDICATORS ARMED COMPUTERIZED SECURITY SYSTEM STATUS GEMINI R 1 2 3 B 4 5 6 C 7 8 9 0 P Q G U SYSTEM ARMED 0

40 NAPCO LIMITED WARRANTY NAPCO SECURITY SYSTEMS, INC. (NAPCO) warrants its products to be free from manufacturing defects in materials and workmanshi

5 KEYPAD CONTROLS & INDICATORS Window. Displays system status messages, zone descriptions, etc. STATUS Light. Lights (green) to indicate that the

6 ARMING AWAY: SETTING THE ALARM WHEN LEAVING ZONES FAULTED 02 BACK DOOR BYPASSED BYPASSED BYPASSED 02 BACK DOOR Arming

7 ARMING AWAY: SETTING THE ALARM WHEN LEAVING System Trouble If you attempt to arm with a “SYSTEM TROUBLE” display alternating with an indicated trou

8 Arming in STAY Mode Interior Zones, when bypassed, allow free movement within the home while the protection of armed perimeter zones is maintained.

9 ARMING STAY: PROTECTING YOURSELF AT HOME Easy Exit (Optional - Easy Exit programmed? YES NO) Your system may have been programmed for Easy Exi